Page 26 - 2016 Healey Performance Catalogue

26 D N E P O T E N I G N E R E D N I L Y C 6 CAMSHAFTS EXCHANGE CAMSHAFTS PROFILES In 2003 we totally revised not only the way Reground old units limit the lobe size and DWR 1 profile is the only camshaft which we sell our camshafts but also the design position, with this in mind we only accept will fit without any valve pocket reliefs. This and manufacturing. We now only sell old units which have not been reground profile is a little better than the BJ8 cam camshafts packaged complete with before, both on the lobes and journals. and so works well in any standard or mildly followers and cam lube for assembly. We Using the original material we heat-treat tuned car. offer the choice of our bucket or standard these to the best limits available. DWR 8 profile is a higher lift with mild type cam followers, please specify when ENG657/1 DWR 1 Mild Road £295-00 duration (requires valve pockets). This ordering (pushrods not included). There are CENG657/8 DWR 8 Fast Road / Mild Rally £295-00 profile is ideal for fast road or mild rally and considerable differences between new and CENG657/2 DWR 2 Race / Rally - 300 degree £295-00 works well with twin 2" SU’s or triple reground cams so the decision should be CENG657/3 DWR 3 Full Race - 320 degree £295-00 Webers for a smooth tractable car. taken carefully. To purchase an exchange camshaft kit for outright sale with no old unit please add £100.00 surcharge. DWR 2 profile is high lift with 300 degrees NEW CAMSHAFTS duration (requires valve pockets). This The relative positioning and relationship BUCKET CAM FOLLOWERS profile is very similar to the original ‘Works’ These are much lighter than standard. Not between cam and follower is unique to our profile and ideal for rally or track day cars only reducing the valve train weight, by design in order to promote follower rotation and works well with triple Webers for a design they also reduce the side loading of at low rpm. These camshafts are also gun punch of power as it comes on cam. the follower and subsequent block wear. drilled through their entire length, with oil DWR 3 profile is high lift with 320 degrees They must be used with our long tubular feed holes in each lobe base circle and the duration (requires valve pockets). This push rods (below). oil pump drive gear, thus giving a positive profile is very similar to the DWR 2 with a pressure fed oil feed to every hard working CENG660B each £9-79 little extra duration and overlap. Ideal for part of the cam and follower. The material LONG TUBULAR PUSH RODS TO SUIT race cars and works well with triple Webers. used is the best available for long life and is BUCKET FOLLOWERS FOR CAM TIMING CHARTS SEE OUR WEBSITE fully heat-treated with the lobes made as Made from chrome-moly tube these are large as possible to reduce wear. Also now very strong and are normally supplied to the available as a Billet Blank for final profiling MODIFIED CAM FOLLOWERS correct length to achieve the combined and heat treatment to your specification, by These new original type cam followers are standard follower and push rod length. These ourselves or your cam grinder. modified in our machine shop to increase can be made to a specific length if required. ENG656/1 DWR 1 Mild Road £595-00 lubrication to the cam lobes and also help CENG661 set of 12 £195-00 CENG656/8 DWR 8 Fast Road / Mild Rally £595-00 the cam follower run lighter as they will not CENG656/2 DWR 2 Race / Rally - 300 degree £595-00 fill with oil. CENG656/3 DWR 3 Full Race - 320 degree £595-00 CENG660 each £9-79 CENG656B Billet blank camshaft £385-00 PLEASE STATE WITH ORDER WHICH TYPE OF CAM FOLLOWERS REQUIRED REMEMBER CAM PRICES INCLUDE FOLLOWERS AND CAM LUBE BUT NOT PUSHRODS. www.bighealey.co.uk Please add VAT & carriage to all prices for UK and EEC consumer sales at the current rate